This page is available under the Creative Commons No Rights Reserved License
Last modified by Ronald Burkey on 2020-04-11
This page provides links to mil-spec parts referenced in Apollo
engineering drawings that I've downloaded from public sources,
primarily the U.S. government ASSIST
site. Background
information about scanned Apollo-specific drawings and the
engineering-drawing indices are provided on the
electro-mechanical page. Note the following related
resources as well:
Only mil-spec drawings free of copyright restrictions are
provided here at Virtual AGC. The most prominent examples of
copyright-restricted drawings needed for the Apollo
G&N systems, but which I've had to exclude, are the NASxxxx
specs from the Aerospace
Industries Association. In some cases NASxxxx
specs supersede or are superseded by MSxxxx mil
specs. In those few cases I have added the parts to the
table below, but the hyperlinks are to the associated MSxxxx
spec rather than to the NASxxxx spec itself ... a procedure
which I admit is questionable technically. Here is a list of
some NASxxxx specs for which I've not been able to identify
associated MSxxxx specs at all: NAS145, NAS620,
NAS662, NAS671, NAS674, NAS1219, NAS1394, NAS1402, NAS1515,
NAS1598. You can probably probably read all of the
NASxxxx specs online by googling for them, even if I cannot
legally post them here.
Concerning revision levels of these drawings, I've been somewhat
inconsistent. For drawings I added early in the process, I
typically used the most-recent revision I could find (often
posting multiple versions), along with any amendments.
Somewhat belatedly, I realized that (obviously!) the Apollo
developers did not have those later document revisions,
and that instead I should be posting the document revisions that
were most contemporaneous to the Apollo program. In other
words, we should have the materials the Apollo developers were
familiar with at the time. So later on, I began posting
earlier revisions, but I did not go back and redo my earlier
postings. Not that I usually had much of a selection of
revisions to choose from anyway. Oh, well! If you
don't like the revisions I've posted here, go try and find your
own. Send them to me, if you like.
| Link | Drawing | Rev | Type |
Sheet | Frame | Title | Notes |
| drawing | A-A-59474 |
C |
1 |
1 |
1 |
INSULATION TAPE, ELECTRICAL; HIGH
TEMPERATURE, POLYTETRAFLOUROETHEYLENE, PRESSURE SENSITIVE |
|
| drawing | AN345 |
6 |
1 |
1 |
1 |
NUT, PLAIN, HEXAGON, NON-STRUCTURAL, FINE
THREAD |
|
| drawing | AN363 |
6 |
1 |
1 |
1 |
NUT, SELF-LOCKING, 550°F | |
| drawing | AN365 |
- |
1 |
1 |
1 |
NUT, SELF LOCKING, 250°F | No copy of AN365 has been located. The
link is to MS20365, which supersedes it. |
| drawing | AN500 |
7 |
1 |
1 |
1 |
SCREW, MACHINE, FILLISTER HEAD, COARSE THREAD |
|
| drawing |
AN505 |
7 |
1 |
1 |
1 |
SCREW, MACHINE, FLAT HEAD, 82 DEGREE, COARSE
THREAD |
|
| drawing |
AN507 |
6 |
1 |
1 |
1 |
SCREW, MACHINE, FLAT HEAD, 100 DEGREE |
The scan of AN507 is a bit illegible in places. It may also be helpful to refer to MS24693, which supersedes it. |
| drawing |
AN510 |
6 |
1 |
1 |
1 |
SCREW, MACHINE, FLAT HEAD, 82 DEGREE, FINE
THREAD |
|
| drawing | AN520 |
- |
1 |
1 |
1 |
SCREW, MACHINE, ROUND HEAD, FINE THREAD |
I could not obtain AN520. The link is
to MS35207, one of the documents suggested to be used in its
place (MS35207, MS35215, MS35219, or MS51958). |
| drawing | AN565 |
7 |
1 |
1 |
1 |
SETSCREW-HEXAGON AND FLUTED SOCKET, HEADLESS |
|
| drawing | AN931 |
- |
1 |
1 |
1 |
GROMMET - ELASTIC | I could not obtain AN931. The link is
to its superseding document MS35489. |
| drawing | AN960 |
21 |
1 |
1 |
1 |
WASHER, FLAT |
|
| drawing | AN6227 |
9 |
1 |
1 |
1 |
PACKING, O, RING HYDRAULIC |
|
| drawing | AN104606 |
3 |
1 |
1 |
1 |
BOLD - CRES HEX HEAD, .190-32 |
See also amendment 1. |
| drawing | AN104608 |
3 |
1 |
1 |
1 |
BOLD - CRES HEX HEAD, .190-32 | See also amendment 1. |
| drawing | AN122691 |
2 |
1 |
1 |
1 |
PIN - DOWEL, STEEL |
|
| drawing | AN122692 |
2 |
1 |
1 |
1 |
PIN - DOWEL, STEEL |
|
| drawing | AN124953 |
3 |
1 |
1 |
1 |
RIVET - 100° COUNTERSUNK HEAD CORROSION
RESISTANT STEEL |
|
| drawing |
AN124954 |
3 |
1 |
1 |
1 |
RIVET - 100° COUNTERSUNK HEAD CORROSION RESISTANT STEEL | |
| drawing | DOD-D-1000 |
B |
1 |
1 |
1 |
DRAWINGS, ENGINEERING AND ASSOCIATED LISTS |
|
| drawing | FED-STD-595 |
C |
1 |
1 |
1 |
COLORS USED IN GOVERNMENT PROCUREMENT |
|
| drawing | MIL-A-5092 |
- |
1 |
1 |
1 |
ADHESIVE, RUBBER BASE, GENERAL PURPOSE |
No copy of MIL-A-5092 has been found.
The link is to MMM-A-1617, which supersedes it. |
| drawing | MIL-A-8625 |
F |
1 |
1 |
1 |
ANODIC COATINGS FOR ALUMINUM AND ALUMINUM
ALLOWS |
See also amendment 1. |
| drawing | MIL-A-8576 |
C |
1 |
1 |
1 |
ADHESIVE, ACRYLIC BASE, FOR ACRYLIC BASE
PLASTIC |
|
| drawing | MIL-A-13883 |
- |
1 |
1 |
1 |
ADHESIVE, SYNTHETIC-RUBBER (HOT OR COLD
BONDING) |
I haven't been able to find a copy. The
link is to MMM-A-189, which supersedes it. |
| drawing | MIL-A-25055 |
- |
1 |
1 |
1 |
ADHESIVE, ACRYLIC MONAMER AND POLYMER BASE,
FOR ACRYLIC PLASTICS |
No copy of MIL-A-25055 has been found.
The link is to MIL-A-8576, which supersedes it. |
| drawing | MIL-C-5541 |
E |
1 |
1 |
1 |
CHEMICAL CONVERSION COATINGS ON ALUMINUM AND
ALUMINUM ALLOYS |
|
| drawing | MIL-C-25050 |
A |
1 |
1 |
1 |
COLORS, AERONAUTICAL LIGHTS AND LIGHTING
EQUIPMENT, GENERAL SPECIFICATIONS FOR |
See also amendments 1
and 2. |
| drawing | MIL-D-1000 |
- |
1 |
1 |
1 |
DRAWINGS, ENGINEERING AND ASSOCIATED LISTS | We don't have a copy of MIL-D-1000. The
link is to DOD-D-1000, which superseded it. |
| drawing | MIL-D-3716 |
A |
1 |
1 |
1 |
DESICCANTS, ACTIVATED FOR DYNAMIC
DEHUMIDIFICATION |
See also amendment 2. |
| drawing | MIL-D-70327 |
- |
1 |
1 |
1 |
DRAWINGS, ENGINEERING AND ASSOCIATED LISTS |
See also amendment 1. |
| drawing | MIL-DTL-27434 |
A |
1 |
1 |
1 |
ADAPTER, CONNECTOR, COAXIAL, RADIOFREQUENCY, BETWEEN SERIES, SERIES BNC to SERIES SM TYPE UG-690/U | |
| drawing | MIL-F-14256 |
E |
1 |
1 |
1 |
FLUX, SOLDERING, LIQUID, PASTE FLUX, SOLDER
PASTE AND SOLDER-PASTE FLUX (FOR ELECTRONIC/ELECTRICAL USE),
GENERAL SPECIFICATION FOR |
|
| drawing | MIL-G-3278 |
A |
1 |
1 |
1 |
GREASE, AIRCRAFT AND INSTRUMENT (FOR LOW AND
HIGH TEMPERATURES) |
We don't have a copy of MIL-G-3278. The
link is to MIL-PRF-23827, which superseded it. |
| drawing | MIL-G-4343 |
C |
1 |
1 |
1 |
GREASE, PNEUMATIC SYSTEM |
|
| drawing | MIL-G-25760 |
- |
1 |
1 |
1 |
GREASE, AIRCRAFT, BALL AND ROLLER BEARING,
WIDE TEMPERATURE RANGE (ASG) |
We don't have a copy of MIL-G-25760.
The link is to MIL-PRF-81322, which superseded it. |
| drawing | MIL-I-631 |
D |
1 |
1 |
1 |
INSULATION, ELECTRICAL, SYNTHETIC - RESIN
COMPOSITION, NONRIGID |
See also amendments 1,
2,
3,
4,
5,
6. |
| drawing | MIL-I-695 |
B |
1 |
1 |
1 |
INSULATION, ELECTRICAL, PAPER (SLOT CELL) |
|
| drawing | MIL-I-15126 |
F |
1 |
1 |
1 |
INSULATION TAPE, ELECTRICAL, PRESSURE
SENSITIVE ADHESIVE AND PRESSURE SENSITIVE THERMOSETTING
ADHESIVE |
See also amendment 4. |
| drawing | MIL-I-19166 |
C |
1 |
1 |
1 |
INSULATION TAPE, ELECTRICAL,
HIGH-TEMPERATURE, GLASS FIBER, PRESSURE-SENSITIVE |
|
| drawing | MIL-I-22129 |
C |
1 |
1 |
1 |
INSULATION TUBING, ELECTRICAL,
POLYTETRAFLUOROETHYLENE RESIN, NONRIGID |
|
| drawing | MIL-I-23053 |
D |
1 |
1 |
1 |
INSULATION SLEEVING, ELECTRICAL, HEAT
SHRINKABLE, GENERAL SPECIFICATIONS FOR |
|
| drawing | MIL-I-23594 |
C |
1 |
1 |
1 |
INSULATION TAPE, ELECTRICAL, HIGH
TEMPERATURE, POLYTETRAFLOUROETHYLENE, PRESSURE-SENSITIVE |
|
| drawing | MIL-M-7866 |
C |
1 |
1 |
1 |
MOLYBDENUM DISULFIDE, TECHNICAL, LUBRICATION
GRADE |
|
| drawing | MIL-P-5425 |
D |
1 |
1 |
1 |
PLASTIC SHEET, ACRYLIC, HEAT RESISTANT |
|
| drawing | MIL-P-7788 |
F |
1 |
1 |
1 |
PANELS, INFORMATION, INTEGRALLY ILLUMINATED |
|
| drawing |
MIL-P-8585 |
- |
1 |
1 |
1 |
PRIMER COATING, ZINC CHROMATE,
LOW-MOISTURE-SENSITIVITY |
No copy of MIL-P-8585 has been found.
The link is to TT-P-1757, which supersedes it. |
| drawing | MIL-P-18177 |
C |
1 |
1 |
1 |
PLASTIC SHEET, LAMINATED, THERMOSETTING,
GLASS FIBER BASE, EPOXY-RESIN |
See also amendment 2. |
| drawing | MIL-P-23377 |
F |
1 |
1 |
1 |
PRIMER COATINGS: EPOXY, CHEMICAL AND SOLVENT
RESISTANT |
|
| drawing |
MIL-P-27316 |
- |
1 |
1 |
1 |
PRIMER COATING, EPOXY, FOR METAL SURFACES |
No copy of MIL-P-27316 has been found.
The link is to MIL-P-23377, which supersedes it. |
| drawing | MIL-PRF-23827 |
C |
1 |
1 |
1 |
GREASE, AIRCRAFT AND INSTRUMENT, GEAR AND
ACTUATOR SCREW |
|
| drawing | MIL-PRF-81322 |
G |
1 |
1 |
1 |
GREASE, AIRCRAFT, GENERAL PURPOSE, WIDE
TEMPERATURE RANGE, NATO CODE G-395 |
|
| drawing | MIL-R-6130 |
C |
1 |
1 |
1 |
RUBBER, CELLULAR, CHEMICALLY BLOWN |
|
| drawing | MIL-S-8660 |
C |
1 |
1 |
1 |
SILICONE COMPOUND, NATO CODE NUMBER S-736 |
|
| drawing | MIL-S-22473 |
E |
1 |
1 |
1 |
SEALING, LEAKING, AND RETAINING COMPOUNDS
(SINGLE COMPONENT) |
|
| drawing | MIL-STD-100 |
D |
1 |
1 |
1 |
ENGINEERING DRAWINGS |
|
| drawing | MIL-STD-100 | G |
1 |
1 |
1 |
ENGINEERING DRAWINGS | |
| drawing | MIL-STD-202 |
H |
1 |
1 |
1 |
ELECTRONIC AND ELECTRICAL COMPONENT PARTS |
|
| drawing | MIL-T-713 |
E |
1 |
1 |
1 |
TWINE, FIBROUS: IMPREGNATED, LACING AND TYING |
|
| drawing | MIL-T-27730 |
A |
1 |
1 |
1 |
TAPE, ANTISEIZE, POLYTETRAFLUOROETHYLENE,
WITH DISPENSER |
|
| drawing | MIL-T-55155 |
C |
1 |
1 |
1 |
TERMINALS, FEEDTHRU (INSULATED) AND
TERMINALS, STUD (INSULATED AND NONINSULATED) |
|
| drawing | MIL-W-16878 |
F |
1 |
1 |
1 |
WIRE, ELECTRICAL, INSULATED, GENERAL
SPECIFICATION FOR |
|
| drawing |
MMM-A-181 |
D |
1 |
1 |
1 |
ADHESIVES, PHENOL, RESORCINOL, OR MELAMINE
BASE |
|
| drawing | MMM-A-189 |
C |
1 |
1 |
1 |
ADHESIVE, SYNTHETIC-RUBBER, THERMOPLASTIC,
GENERAL-PURPOSE |
|
| drawing | MMM-A-1617 |
B |
1 |
1 |
1 |
ADHESIVE, RUBBER BASE, GENERAL PURPOSE |
|
| drawing | MS3368 |
F |
1 |
1 |
1 |
STRAP, TIEDOWN, ELECTRICAL COMPONENTS,
IDENTIFICATION, ADJUSTABLE, SELF CLINCHING, PLASTIC, TYPE
II, CLASS 1 |
|
| drawing | MS9021 |
D |
1 |
1 |
1 |
PACKING, PREFORMED, (O) RING |
|
| drawing | MS9461 |
A |
1 |
1 |
1 |
BALL, BEARING - PRECISION GRADE, AMS 7445 |
|
| drawing |
MS15795 |
G | 1 |
1 |
1 |
WASHER, FLAT-METAL, ROUND, GENERAL PURPOSE |
|
| drawing | MS16200 |
- |
1 |
1 |
1 |
SCREWS, MACHINE, PAN HEAD, SLOTTED, CORROSION
RESISTING STEEL, PASSIVATED, UNC-2A NONMAGNETIC |
No copy of MS16200 has been located.
The link is to MS51957, which superseded MS16200. |
| drawing | MS16214 |
- |
1 |
1 |
1 |
WASHER, LOCK, SPRING, NONLINK, MEDIUM SERIES,
NON-MAGNETIC |
We don't have a copy of MS16214. The
link is to MS35338, which superseded it. |
| drawing | MS16535 | J |
1 |
1 |
1 |
RIVET - TUBULAR, OVAL HEAD |
|
| drawing | MS16555 | C |
1 |
1 |
1 |
PIN, STRAIGHT, HEADLESS (DOWEL) (.0002 OVER NOMINAL SIZE) |
|
| drawing | MS16556 |
B |
1 |
1 |
1 |
PIN, STRAIGHT, HEADLESS (DOWEL) (.001 OVER
NOMINAL SIZE) |
|
| drawing | MS16562 |
C |
1 |
1 |
1 |
PIN, SPRING - TUBULAR, SLOTTED |
|
| drawing | MS16628 |
B |
1 |
1 |
1 |
RING, RETAINING, EXTERNAL, BOWED (TAPERED
SECTION TYPE) |
|
| drawing | MS16624 |
C |
1 |
1 |
1 |
RING, RETAINING, EXTERNAL, BASIC (TAPERED
SECTION TYPE) |
|
| drawing | MS16625 |
E |
1 |
1 |
1 |
RING, RETAINING, INTERNAL, BASIC (TAPERED
SECTION TYPE) |
|
| drawing | MS16633 | D |
1 |
1 |
1 |
RING, RETAINING, EXTERNAL, "E" (REDUCED SECTION TYPE) |
|
| drawing | MS16995 | H |
1 |
1 |
1 |
SCREW, CAP, SOCKET HEAD-HEXAGON, CORROSION RESISTANT
STEEL, UNC-3A |
|
| drawing | MS16996 | F | 1 |
1 |
1 |
SCREW, CAP, SOCKET HEAD-HEXAGON, CORROSION
RESISTANT STEEL, UNF-3A |
|
| drawing | MS16997 |
D |
1 |
1 |
1 |
SCREW, CAP, SOCKET HEAD AND SCREW, CAP,
SOCKET HEAD, SELF-LOCKING, ALLOY STEEL, CADMIUM PLATED,
UNC-3A
|
|
| drawing |
MS16998 |
E |
1 |
1 |
1 |
SCREW, CAP, SOCKET HEAD AND SCREW, CAP, SOCKET HEAD, SELF-LOCKING: ALLOY STEEL, CADMIUM PLATED, UNF-3A | |
| drawing | MS17121 |
- |
1 |
1 |
1 |
TERMINAL, STUD, SINGLE TURRET |
No copy of MS17121 is available. It was
superseded by MIL-T-55155/29A, which is the document linked |
| drawing |
MS17122 |
- |
1 |
1 |
1 |
TERMINAL, STUD, SINGLE TURRET |
No copy of MS17122 is available. It was
superseded by MIL-T-55155/30A, which is the document linked. |
| drawing | MS17182 |
E |
1 |
1 |
1 |
TERMINAL, LUG, CRIMP STYLE, COPPER, INSULATED
(SERVO COMPONENTS) TYPE II, CLASS 1, FOR 125 DEGREES C TOTAL
CONDUCTOR TEMPERATURE |
|
| drawing | MS17156 |
A |
1 |
1 |
1 |
TERMINAL, STUD, FEEDTHRU, SINGLE-DOUBLE |
|
| drawing | MS17803 |
- |
1 |
1 |
1 |
CONTACT, ELECTRIC, PIN, CRIMP REMOVABLE, SIZE
16 AND 20 |
The link is to MIL-C-39029/34B, which
superseded MS17803. |
| drawing | MS17804 |
- |
1 |
1 |
1 |
CONTACTS, ELECTRIC, SOCKET, CRIMP REMOVABLE,
SIZE 16 AND 20 |
The link is to MIL-C-39029/35B, which superseded MS17804. |
| drawing | MS18035 |
- |
1 |
1 |
1 |
STRAP, CABLE, IDENTIFICATION ADJUSTABLE,
PLASTIC, TYPE 2, CLASS 2 |
No copy of MS18035 is available. The
link is to MS3368, which superseded it. |
| drawing | MS20341 | C | 1 |
1 |
1 |
NUT, PLAIN, HEXAGON, ELECTRICAL |
|
| drawing | MS20364 | C | 1 |
1 |
1 |
NUT, SELF LOCKING, THIN, 250°F | The only scan
of MS20364 that we have is pretty illegible.
Partial replacements are MS21042, MS21083, or MS21245, but
the Link column links to MS21083 which seems to
cover all of the required configurations in the Apollo
G&N drawings as of this writing. |
| drawing | MS20365 |
C |
1 |
1 |
1 |
NUT, SELF LOCKING, 250°F | |
| drawing | MS20426 | L | 1 |
1 |
1 |
RIVET, SOLID, COUNTERSUNK 100°, PRECISION HEAD, ALUMINUM AND TITANIUM COLUMBIUM ALLOY | |
| drawing | MS20450 |
C |
1 |
1 |
1 |
RIVET, TUBULAR |
|
| drawing | MS20470 |
H |
1 |
1 |
1 |
RIVET, SOLID UNIVERSAL HEAD, ALUMINUM ALLOY AND TITANIUM COLUMBIUM ALLOY | |
| drawing | MS20995 |
E |
1 |
1 |
1 |
WIRE, SAFETY OR LOCK |
|
| drawing | MS21042 |
M |
1 |
1 |
1 |
NUT, SELF-LOCKING, 450°F, REDUCED HEXAGON,
REDUCED HEIGHT, RING BASE, NON-CORROSION RESISTANT STEEL |
|
| drawing | MS21043 | E | 1 |
1 |
1 |
NUT, SELF-LOCKING, 800°F, REDUCED HEXAGON,
REDUCED HEIGHT, RING BASE, CORROSION RESISTANT STEEL |
|
| drawing | MS21045 | L | 1 |
1 |
1 |
NUT, SELF-LOCKING, HEXAGON - REGULAR HEIGHT,
450°F, 125 KSI FTU |
|
| drawing | MS21046 | D | 1 |
1 |
1 |
NUT, SELF-LOCKING, HEXAGON - REGULAR HEIGHT,
800°F, 125 KSI FTU |
|
| drawing | MS21059 |
J |
1 |
1 |
1 |
NUT, SELF-LOCKING, PLATE, TWO LUG, FLOATING, LOW HEIGHT STEEL, 125 KSI FTU, 450°F | |
| drawing | MS21083 | H | 1 |
1 |
1 |
NUT, SELF-LOCKING, HEXAGON, NON-METALLIC INSERT, LOW HEIGHT, 250°F | |
| drawing |
MS21087 |
B |
1 |
1 |
1 |
NUT, SELF-LOCKING, PLATE, SIDE BY SIDE
REDUCED RIVET SPACING, LOW HEIGHT, CRES, 125 KSI FTU, 450
DEG. AND 800 DEG. F |
|
| drawing | MS21208 | B | 1 |
1 |
1 |
INSERT, SCREW THREAD, COARSE AND FINE, FREE
RUNNING, HELICAL COIL, CRES |
|
| drawing | MS21209 | E | 1 |
1 |
1 |
INSERT, SCREW THREAD, COARSE AND FINE, SCREW
LOCKING, HELICAL COIL, CRES |
|
| drawing | MS21268 |
A |
1 |
1 |
1 |
SCREW, INSTRUMENT - FILISTER HEAD |
|
| drawing | MS21269 |
B |
1 |
1 |
1 |
SCREW, INSTRUMENT - PAN HEAD |
The linked document is actually a
cancellation notice, but it appears to contain the complete
contents of the pre-cancelation document. |
| drawing | MS24367 |
C |
1 |
1 |
1 |
LAMP, INCANDESCENT - MINIATURE INTEGRAL
LIGHTING |
|
| drawing | MS24585 | D | 1 |
1 |
1 |
SPRINGS, HELICAL, COMPRESSION: FOR LOADS
BELOW 20 POUNDS |
|
| drawing |
MS24622 |
D |
1 |
1 |
1 |
SCREW, TAPPING-THREAD FORMING, TYPE B, PAN
HEAD, CROSSED-RECESSED, CORROSION-RESISTING STEEL |
|
| drawing | MS24671 | C | 1 |
1 |
1 |
SCREW, CAP, SOCKET-HEAD-FLAT COUNTERSUNK,
82°, CORROSION-RESISTING STEEL, UNC-3A |
|
| drawing | MS24692 |
D |
1 |
1 |
1 |
PIN, TAPERED, PLAIN |
|
| drawing | MS24693 | K | 1 |
1 |
1 |
SCREW, MACHINE, FLAT COUNTERSUNK HEAD, 100°, CROSS RECESSED, UNC-2A AND UNF-2A | |
| drawing | MS25036 |
P |
1 |
1 |
1 |
TERMINAL, LUG, CRIMP STYLE, COPPER,
INSULATED, RING TONGUE, BELL MOUTHED, TYPE II, CLASS I (FOR
105 DEG. C TOTAL CONDUCTOR TEMPERATURE) |
|
| drawing | MS25281 | K | 1 |
1 |
1 |
CLAMP, LOOP, PLASTIC, WIRE SUPPORT |
|
| drawing | MS27197 |
B |
1 |
1 |
1 |
SEAL PLAIN, RUBBER (HOT RESISTANT 400°F) MOLD
IN GROOVE |
|
| drawing | MS28775 | E | 1 |
1 |
1 |
PACKING, PREFORMED, HYDRAULIC, +275°F ("O"
RING) |
|
| drawing | MS35200 |
- |
1 |
1 |
1 |
SCREW, MACHINE-FLAT COUNTERSUNK HEAD,
82°,CROSS-RECESSED, CORROSION-RESISTANT STEEL, UNC-2A |
The link is to MS51959, which superseded
MS35200. |
| drawing | MS35201 |
- |
1 |
1 |
1 |
SCREW, MACHINE, FLAT COUNTERSUNK HEAD,
CROSS-RECESSED, CORROSION RESISTING STEEL, PASSIVATED, NF-21
- UNF-2A |
The link is to MS51960, which superseded
MS35201. |
| drawing |
MS35207 |
F |
1 |
1 |
1 |
SCREW, MACHINE - PAN HEAD, CROSS-RECESSED,
CARBON STEEL, CADMIUM PLATED, UNF-2A |
|
| drawing | MS35216 | A | 1 |
1 |
1 |
SCREW, MACHINE, PAN HEAD, CROSS-RECESSED,
CORROSION RESISTING STEEL, PASSIVATED, NC-2A AND UNC-2A |
|
| drawing | MS35223 | B | 1 |
1 |
1 |
SCREW, MACHINE, PAN HEAD, SLOTTED, CARBON
STEEL, CADMIUM PLATED, NC-2A AND UNC-2A |
|
| drawing | MS35233 | A | 1 |
1 |
1 |
SCREW, MACHINE, PAN HEAD, SLOTTED, CORROSION
RESISTING STEEL, PASSIVATED, NC-2A AND UNC-2A |
|
| drawing | MS35234 |
A |
1 |
1 |
1 |
SCREW, MACHINE, PAN HEAD, SLOTTED, CORROSION
RESISTING STEEL, PASSIVATED, NF-2A AND UNF-2A |
|
| drawing | MS35249 |
A |
1 |
1 |
1 |
SCREW, MACHINE, FLAT COUNTERSUNK HEAD,
SLOTTED, CORROSION RESISTING STEEL, PASSIVATED, NC-2A AND
UNC-2A |
|
| drawing | MS35324 |
- |
1 |
1 |
1 |
CONNECTOR, ADAPTER UG-565A/U, TYPE C TO TYPE N, RF | I have been unable to obtain a copy of
MS35324. MS35324 was superseded by MIL-A-27434, which
was superseded by MIL-DTL-27434. The link is to the
latter. |
| drawing | MS35333 | J | 1 |
1 |
1 |
WASHER, LOCK, FLAT-INTERNAL TOOTH |
|
| drawing | MS35333 | K | 1 |
1 |
1 |
WASHER, LOCK, FLAT-INTERNAL TOOTH | |
| drawing | MS35335 |
G |
1 |
1 |
1 |
WASHER, LOCK, FLAT-EXTERNAL TOOTH |
|
| drawing | MS35337 | B | 1 |
1 |
1 |
WASHER, LOCK, SPLIT, HELICAL, LIGHT SERIES |
|
| drawing | MS35338 | J | 1 |
1 |
1 |
WASHER, LOCK-SPRING, HELICAL, REGULAR
(MEDIUM) SERIES |
|
| drawing | MS35338 | L | 1 |
1 |
1 |
WASHER, LOCK-SPRING, HELICAL, REGULAR
(MEDIUM) SERIES |
|
| drawing | MS35489 |
J |
1 |
1 |
1 |
GROMMETS, SYNTHETIC AND SILICONE RUBBER, HOT-OIL AND COOLANT RESISTANT | |
| drawing | MS35650 |
G |
1 |
1 |
1 |
NUT, PLAIN, HEXAGON, MACHINE SCREW, UNF-2B |
|
| drawing | MS35457 | B | 1 |
1 |
1 |
SCREW, CAP, SOCKET HEAD-HEXAGON, ALLOY STEEL,
CADMIUM OR ZINC, UNC-3A |
|
| drawing | MS35649 | H | 1 |
1 |
1 |
NUT, PLAIN, HEXAGON, MACHINE SCREW UNC-2B |
|
| drawing | MS35690 |
E |
1 |
1 |
1 |
NUT, PLAIN, HEXAGON, UNC-2B AND UNF-2B |
|
| drawing | MS39086 |
B |
1 |
1 |
1 |
PIN, SPRING |
|
| drawing | MS51021 |
C |
1 | 1 |
1 | SETSCREW-HEXAGON SOCKET, CUP POINT, CORROSION
RESISTING (CHROME-NICKEL) STEEL, PASSIVATED, UNC-3A PLAIN
AND SELF LOCKING |
|
| drawing | MS51023 |
C |
1 |
1 |
1 |
SETSCREW-HEXAGON SOCKET, CUP POINT,
CORROSION-RESISTING STEEL, PASSIVATED, UNF-3A, PLAIN AND
SELF-LOCKING |
|
| drawing | MS51029 |
B |
1 |
1 |
1 |
SETSCREW-HEXAGON, SOCKET, FLAT POINT,
CORROSION-RESISTING STEEL, PASSIVATED, UNC-3A, PLAIN AND
SELF-LOCKING |
|
| drawing | MS51045 |
B |
1 |
1 |
1 |
SETSCREW-HEXAGON SOCKET, HALF-DOG POINT,
CORROSION-RESISTING STEEL, PASSIVATED, UNC-3A |
|
| drawing | MS51053 | A | 1 |
1 |
1 |
SETSCREW, FLUTED SOCKET, ALLOY STEEL, CADMIUM
PLATED, NC-3A |
|
| drawing | MS51923 | C |
1 |
1 |
1 |
PIN, SPRING-TABULAR, COILED, MEDIUM DUTY |
|
| drawing | MS51957 | D | 1 |
1 |
1 |
SCREW, MACHINE, PAN HEAD, CROSS-RECESSED,
CORROSION RESISTANT STEEL, UNC-2A |
|
| drawing | MS51959 | D | 1 |
1 |
1 |
SCREW, MACHINE, FLAT COUNTERSUNK HEAD, 82°,
CROSS-RECESSED, CORROSION-RESISTANT STEEL, UNC-2A |
|
| drawing | MS51960 |
C |
1 |
1 |
1 |
SCREW, MACHINE-FLAT COUNTERSUNK HEAD, 82°,
CROSS-RECESSED, CORROSION RESISTANT STEEL, UNF-2A |
|
| drawing | MS51960 | D |
1 |
1 |
1 |
SCREW, MACHINE-FLAT COUNTERSUNK HEAD, 82°, CROSS-RECESSED, CORROSION RESISTANT STEEL, UNF-2A | |
| drawing | MS122159 |
D |
1 |
1 |
1 |
INSERT CRES HELICAL COIL COARSE THREAD 2 DIA.
NOMINAL LENGTH |
|
| drawing | MS134354 |
- |
1 |
1 |
1 |
BALL - CORROSION RESISTANT STEEL, PRECISION
GRADE |
The link is to MS9461, which superseded
MS134354. |
| drawing | MS171432 |
C |
1 |
1 |
1 |
PIN - SPRING, CORROSION RESISTANT STEEL | |
| drawing | MS171433 |
C |
1 |
1 |
1 |
PIN - SPRING, CORROSION RESISTANT STEEL |
|
| drawing | MS171434 |
C |
1 |
1 |
1 |
PIN - SPRING, CORROSION RESISTANT STEEL | |
| drawing |
MS171435 |
C |
1 |
1 |
1 |
PIN - SPRING, CORROSION RESISTANT STEEL | |
| drawing |
MS171436 | C |
1 |
1 |
1 |
PIN - SPRING, CORROSION RESISTANT STEEL | |
| drawing | MS171494 |
C |
1 |
1 |
1 |
PIN - SPRING, CORROSION RESISTANT STEEL | |
| drawing |
MS171528 |
C |
1 |
1 |
1 |
PIN - SPRING, CORROSION RESISTANT STEEL | |
| drawing | NAS686 |
- |
1 |
1 |
1 |
NUT, SELF-LOCKING, PLATE-TWO LUG, LOW HEIGHT,
C'BORE, FLOATING |
The link is to MS21059, which superseded
NAS686. |
| drawing | NAS1291 |
- |
1 |
1 |
1 |
NUT, SELF-LOCKING, HEXAGON, LOW HEIGHT, LIGHT
WEIGHT |
The link is to MS21043, which is a universal
replacement for NAS1291. |
| drawing |
NAS1351 |
- |
1 |
1 |
1 |
SCREW, CAP, SOCKET HEAD, UNDRILLED AND DRILLED, PLAIN AND SELF LOCKING, ALLOY STEEL AND CORROSION RESISTING STEEL AND HEAT-RESISTANT STEEL, UNRF-3A | I have been unable to obtain a copy of
NAS1351. The link is to MS16998 which was superseded by
NAS1351. |
| drawing | NAS1352 |
- |
1 |
1 |
1 |
SCREW, CAP, SOCKET HEAD, UNDRILLED AND
DRILLED, PLAIN AND SELF-LOCKING, ALLOY STEEL, CORROSION-RESISTANT STEEL AND HEAT-RESISTANT STEEL, UNRC-3A AND UNRC-2A |
The link is to MS16997, which was superseded
by NAS1352. |
| drawing | QQ-A-250 |
F |
1 |
1 |
1 |
ALUMINUM AND ALUMINUM ALLOW PLATE AND SHEET,
GENERAL SPECIFICATION FOR |
|
| drawing | QQ-A-327 |
B |
1 |
1 |
1 |
ALUMINUM ALLOY PLATE AND SHEET 6061 |
We don't have a copy of QQ-A-327. The
link is to QQ-A-240, which superseded it. |
| drawing | QQ-B-575 |
C |
1 |
1 |
1 |
BRAID, WIRE (COPPER, TIN COATED OR SILVER
COATED, TUBULAR OR FLAT) |
|
| drawing | QQ-S-571 |
F |
1 |
1 |
1 |
SOLDER, ELECTRONIC (96 TO 485 DEG. C) |
|
| drawing | QQ-W-343 |
G |
1 |
1 |
1 |
WIRE, ELECTRICAL, COPPER (UNINSULATED) |
|
| drawing |
TT-P-1757 |
A |
1 |
1 |
1 |
PRIMER COATING, ZINC CHROMATE,
LOW-MOISTURE-SENSITIVITY |