Source Code
|
These source-code files are part of a reconstructed copy of Comanche 44, the
initial release (though not the final mission release) of the Apollo 10
Command Module (CM) Apollo Guidance Computer (AGC) software. Subsequent releases
were Comanche 45 and Comanche 45/2 (the flown release on Apollo 10). The reconstruction
is believed to be exactly accurate, but in the absence of an actual Apollo-era
listing of Comanche 44, some explanation of the reconstruction process is needed
to insure confidence in that accuracy.
The starting point was the source code of Comanche 51
(separately previously reconstructed from an Apollo-era listing of Comanche 55,
flown on Apollo 11). Comanche 51 source code was then modified
by undoing changes known to have been made between revisions 44 and 51. The now-reconstructed
Comanche 44 source code was verified by assembling it and checking that the assembled code had
the expected known-correct memory-bank checksums.
Note that page numbers in the reconstructed code match those on the Comanche 55 printout,
although the source code would likely have different page numbers in a contemporary
Comanche 44 listing.
Annotations that were not present in the contemporary source code have been added to the reconstructed
code to justify each change relative to Comanche 51. Here's a guide to the Apollo documentation referenced
in those annotations:
In most cases, only the titles (rather than the full texts) of PCRs are known. In addition to the
explanatory annotations, there is also
a step-by-step commentary about the reconstruction process.
Comments expected to have been present in the original source code are prefixed with a single '#' symbol,
whereas comments added later are prefixed by "##" or "###". Report any errors
noted by creating an
issue report at the Virtual AGC
Project's GitHub repository.
|
060223,000002: ## Copyright: Public domain.
060224,000003: ## Filename: PHASE_TABLE_MAINTENANCE.agc
060225,000004: ## Purpose: A section of Comanche revision 044.
060226,000005: ## It is part of the reconstructed source code for the
060227,000006: ## original release of the flight software for the Command
060228,000007: ## Module's (CM) Apollo Guidance Computer (AGC) for Apollo 10.
060229,000008: ## The code has been recreated from a copy of Comanche 055. It
060230,000009: ## has been adapted such that the resulting bugger words
060231,000010: ## exactly match those specified for Comanche 44 in NASA drawing
060232,000011: ## 2021153D, which gives relatively high confidence that the
060233,000012: ## reconstruction is correct.
060234,000013: ## Assembler: yaYUL
060235,000014: ## Contact: Ron Burkey <info@sandroid.org>.
060236,000015: ## Website: www.ibiblio.org/apollo/index.html
060237,000016: ## Mod history: 2020-12-03 MAS Created from Comanche 51.
060238,000017:
|
|
Page 1404
|
060240,000019: # SUBROUTINE TO UPDATE THE PROGRAM NUMBER DISPLAY ON THE DSKY.
060241,000020:
060242,000021: 43,3726 COUNT 02/PHASE
060243,000022: 5354 BLOCK 02
060244,000023: 4000 SETLOC FFTAG1
060245,000024: 4000 BANK
060246,000025:
060247,000026: 5354 50002 NEWMODEX INDEX Q # UPDATE MODREG. ENTRY FOR MODE IN FIXED.
060248,000027: 5355 30000 CAF 0
060249,000028: 5356 24002 INCR Q
060250,000029:
060251,000030: 5357 55011 NEWMODEA TS MODREG # ENTRY FOR MODE IN A.
060252,000031: 5360 35363 MMDSPLAY CAF +3 # DISPLAY MAJOR MODE.
060253,000032: 5361 22006 PREBJUMP LXCH BBANK # PUTS BBANK IN L
060254,000033: 5362 14704 TCF BANKJUMP # PUTS Q INTO A
060255,000034: 5363 20440 CADR SETUPDSP
060256,000035:
060257,000036: # RETURN TO CALLER +3 IF MODE = THAT AT CALLER +1. OTHERWISE RETURN TO CALLER +2.
060258,000037:
060259,000038: 5364 50002 CHECKMM INDEX Q
060260,000039: 5365 40000 CS 0
060261,000040: 5366 61011 AD MODREG
060262,000041: 5367 00006 EXTEND
060263,000042: 5370 16710 BZF Q+2
060264,000043: 5371 16706 TCF Q+1 # NO MATCH
060265,000044:
060266,000045: 5372 6711 TCQ = Q+2 +1
060267,000046:
060268,000047: 14,3762 BANK 14
060269,000048: 10,2000 SETLOC PHASETAB
060270,000049: 10,2000 BANK
060271,000050:
060272,000051: 10,2440 COUNT 10/PHASE
060273,000052:
060274,000053: 10,2440 00004 SETUPDSP INHINT
060275,000054: 10,2441 52071 DXCH RUPTREG1 # SAVE CALLER-S RETURN 2CADR
060276,000055: 10,2442 34371 CAF PRIO30 # EITHER A TASK OR JOB CAN COME TO
060277,000056: 10,2443 05134 TC NOVAC # NEWMODEX
060278,000057: 10,2444 1011 EBANK= MODREG
060279,000058: 10,2444 03441 60102 2CADR DSPMMJOB
060280,000059:
060281,000060: 10,2446 52071 DXCH RUPTREG1
060282,000061: 10,2447 00003 RELINT
060283,000062: 10,2450 52006 DXCH Z # RETURN
060284,000063:
060285,000064: 10,2451 40,3441 DSPMMJOB EQUALS DSPMMJB
060286,000065:
060287,000066: 5372 BLOCK 02
|
|
Page 1405
|
060289,000068: 4000 SETLOC FFTAG1
060290,000069: 4000 BANK
060291,000070:
|
|
Page 1406
|
060293,000072: # PHASCHNG IS THE MAIN WAY OF MAKING PHASE CHANGES FOR RESTARTS. THERE ARE THREE FORMS OF PHASCHNG, KNOWN AS TYPE
060294,000073: # A, TYPE B, AND TYPE C. THEY ARE ALL CALLED AS FOLLOWS, WHERE OCT XXXXX CONTAINS THE PHASE INFORMATION,
060295,000074: # TC PHASCHNG
060296,000075: # OCT XXXXX
060297,000076: # TYPE A IS CONCERNED WITH FIXED PHASE CHANGES, THAT IS, PHASE INFORMATION THAT IS STORED PERMANENTLY. THESE
060298,000077: # OPTIONS ARE, WHERE G STANDS FOR A GROUP AND .X FOR THE PHASE,
060299,000078: # G.0 INACTIVE, WILL NOT PERMIT A GROUP G RESTART
060300,000079: # G.1 WILL CAUSE THE LAST DISPLAY TO BE REACTIVATED, USED MAINLY IN MANNED FLIGHTS
060301,000080: # G.EVEN A DOUBLE TABLE RESTART, CAN CAUSE ANY COMBINATION OF TWO JOBS, TASKS, AND/OR
060302,000081: # LONGCALL TO BE RESTARTED.
060303,000082: # G.ODD NOT .1 A SINGLE TABLE RESTART, CAN CAUSE EITHER A JOB, TASK, OR LONGCALL RESTART
060304,000083:
060305,000084: # THIS INFORMATION IS PUT INTO THE OCTAL WORD AFTER TC PHASCHNG AS FOLLOWS
060306,000085: # TL0 00P PPP PPP GGG ,
060307,000086: # WHERE EACH LETTER OR NUMBER STANDS FOR A BIT. THE G:S STAND FOR THE GROUP, OCTAL 1-7, THE P:S FOR THE PHASE,
060308,000087: # OCTAL 0 - 127. 0:S MUST BE 0. IF ONE WISHES TO HAVE THE TBASE OF GROUP G TO BE SET AT THIS TIME,
060309,000088: # T IS SET TO 1, OTHERWISE IT IS SET TO 0. SIMIARLY IF ONE WISHES TO SET LONGBASE, THEN L IS SET TO 1, OTHERWISE
060310,000089: # IT IS SET TO 0. SOME EXAMPLES,
060311,000090: # TC PHASCHNG THIS WILL CAUSE GROUP 3 TO BE SET TO 0,
060312,000091: # OCT 00003 MAKING GROUP 3 INACTIVE
060313,000092:
060314,000093: # TC PHASCHNG IF A RESTART OCCURS THIS WOULD CAUSE
060315,000094: # OCT 00012 GROUP 2 TO RESTART THE LAST DISPLAY
060316,000095:
060317,000096: # TC PHASCHNG THIS SETS THE TBASE OF GROUP 4 AND IN
060318,000097: # OCT 40064 CASE OF A RESTART WOULD START UP THE TWO
060319,000098: # THINGS LOCATED IN THE DOUBLE 4.6 RESTART
060320,000099: # LOCATION
060321,000100:
060322,000101: # TC PHASCHNG THIS SETS LONGBASE AND UPON A RESTART
060323,000102: # OCT 20135 CAUSES 5.13 TO BE RESTARTED (SINCE
060324,000103: # LONGBASE WAS SET THIS SINGLE ENTRY
060325,000104: # SHOULD BE A LONGCALL)
060326,000105:
060327,000106: # TC PHASCHNG SINCE BOTH TBASE4 AND LONGBASE ARE SET,
060328,000107: # OCT 60124 4.12 SHOULD CONTAIN BOTH A TASK AND A
060329,000108: # LONGCALL TO BE RESTARTED
060330,000109:
060331,000110: # TYPE C PHASCHNG CONTAINS THE VARIABLE TYPE OF PHASCHNG INFORMATION. INSTEAD OF THE INFORMATION BEING IN A
060332,000111: # PERMANENT FORM, ONE STORES THE DESIRED RESTART INFORMATION IN A VARIABKE LOCATION. THE BITS ARE AS FOLLOWS,
060333,000112: # TL0 1AD XXX CJW GGG
060334,000113: # WHERE EACH LETTER OR NUMBER STANDS FOR A BIT. THE G:S STAND FOR THE GROUP, OCTAL 1 - 7. IF THE RESTART IS TO
060335,000114: # BE BY WAITLIST, W IS SET TO 1, IF IT IS A JOB, J IS SET TO 1, IF IT IS A LONGCALL, C IS SET TO 1. ONLY ONE OF
060336,000115: # THESE THREE BITS MAY BE SET. X:S ARE IGNORED 1 MUST BE 1, AND 0 MUST BE 0. AGAIN T STANDS FOR THE TBASE,
|
|
Page 1407
|
060338,000117: # AND L FOR LONGBASE. THE BITS A AND D ARE CONCERNED WITH THE VARIABLE INFORMATION. IF D IS SET TO 1, A PRIORITY
060339,000118: # OR DELTA TIME WILL BE READ FROM THE NEXT LOCATION AFTER THE OCTAL INFORMATION, IF THIS IS TO BE INDIRECT, THAT
060340,000119: # IS, THE NAME OF A LOCATION COMT+INING THE INFORMATION (DELTA TIME ONLY), THEN THIS IS GIVEN AS THE -GENADR OF
060341,000120: # THAT LOCATION WHICH CONTAINS THE DELTA TIME. IF THE OLD PRIORITY OR DELTA TIME IS TO BE USED, THAT WHICH IS
060342,000121: # ALREADY IN THE VARIABLE STORAGE, THEN D IS SET TO 0. NEXT THE A BIT IS USED. IF IT IS SET TO 0, THE ADDRESS
060343,000122: # THAT WOULD BE RESTARTED DURING A RESTART IS THE NEXT LOCATION AFTER THE PHASE INFORMATION, THAT IS, EITHER
060344,000123: # (TC PHASCHNG) +2 OR +3, DEPENDING ON WHETHER D HAD BEEN SET OR NOT. IF A IS SET TO 1, THEN THE ADDRESS THAT
060345,000124: # WOULD BE RESTARTED IS THE 2CADR THAT IS READ FROM THE NEXT TWO LOCATIONS. EXAMPLES,
060346,000125: # AD TC PHASCHNG THIS WOULD CAUSE LOCATION AD +3 TO BE
060347,000126: # AD+1 OCT 05023 RESTARTED BY GROUP THREE WITH A PRIORITY
060348,000127: # AD+2 OCT 23000 OF 23. NOTE UPON RETURNING IT WOULD
060349,000128: # AD+3 ALSO GO TO AD+3
060350,000129:
060351,000130: # AD TC PHASCHNG GROUP 1 WOULD CAUSE CAUSE CALLCALL TO
060352,000131: # AD+1 OCT 27441 BE STARTED AS A LONGCALL FROM THE TIME
060353,000132: # AD+2 -GENADR DELTIME STORED IN LONGBASE (LONGBASE WAS SET) BY
060354,000133: # AD+3 2CADR CALLCALL A DELTATIME STORED IN DELTIME. THE
060355,000134: # AD+4 BBCON OF THE 2CADR SHOULD CONTAIN THE E
060356,000135: # AD+5 BANK OF DELTIME. PHASCHNG RETURNS TO
060357,000136: # LOCATION AD+5
060358,000137:
060359,000138: # NOTE THAT IF A VARIABLE PRIORITY IS GIVEN FOR A JOB, THE JOB WILL BE RESTARTED AS A NOVAC IF THE PRIORITY IS
060360,000139: # NEGATIVE, AS A FINDVAC IF THE PRIORITY IS POSITIVE.
060361,000140:
060362,000141: # TYPE B PHASCHNG IS A COMBINATION OF VARIABLE AND FIXED PHASE CHANGES. IT WILL START UP A JOB AS INDICATED
060363,000142: # BELOW AND ALSO START UP ONE FIXED RESTART, THAT IS EITHER AN G.1 OR A G.ODD OR THE FIRST ENTRY OF G.EVEN
060364,000143: # DOUBLE ENTRY. THE BIT INFORMATION IS AS FOLLOWS,
060365,000144: # TL1 DAP PPP PPP GGG
060366,000145: # WHERE EACH LETTER OR NUMBER STANDS FOR A BIT. THE G:S STAND FOR THE GROUP, OCTAL 1 - 7. THE P:S FOR THE FIXED
060367,000146: # PHASE INFORMATION, OCTAL 0 - 127. 1 MUST BE 1. AND AGAIN T STANDS FOR THE TBASE AND L FOR LONGBASE. D THIS
060368,000147: # TIME STANDS ONLY FOR PRIORITY SINCE THIS WILL BE CONSIDERED A JOB, AND IT MUST BE GIVEN DIRECTLY IF GIVEN.
060369,000148: # AGAIN A STANDS FOR THE ADDRESS OF THE LOCATION TO BE RESTARTED, 1 IF THE 2CADR IS GIVEN, OR 0 IF IT IS TO BE
060370,000149: # THE NEXT LOCATION. (THE RETURN LOCATION OF PHASCHNG) EXAMPLES,
060371,000150: # AD TC PHASCHNG TBASE IS SET AND A RESTART CAUSE GROUP 3
060372,000151: # AD+1 OCT 56043 TO START THE JOB AJOBAJOB WITH PRIORITY
060373,000152: # AD+2 OCT 31000 31 AND THE FIRST ENTRY OF 3.4SPOT (WE CAN
060374,000153: # AD+3 2CADR AJOBAJOB ASSUME IT IS A TASK SINCE WE SET TBASE3)
060375,000154: # AD+4 UPON RETURN FROM PHASCHNG CONTROL WOULD
060376,000155: # AD+5 GO TO AD+5
060377,000156:
060378,000157: # AD TC PHASCHNG UPON A RESTART THE LAST DISPLAY WOULD BE
060379,000158: # AD+1 OCT 10015 RESTARTED AND A JOB WITH THE PREVIOUSLY
060380,000159: # AD+2 STORED PRIORITY WOULD BE BEGUN AT AD+2
060381,000160: # BY MEANS OF GROUP 5
|
|
Page 1408
|
060383,000162: # THE NOVAC-FINDVAC CHOICE FOR JOBS HOLDS HERE ALSO - NEGATIVE PRIORITY CAUSES A NOVAC CALL, POSITIVE A FINDVAC.
060384,000163:
060385,000164: # SUMMARY OF BITS
060386,000165: # TYPE A TL0 00P PPP PPP GGG
060387,000166: # TYPE B TL1 DAP PPP PPP GGG
060388,000167: # TYPE C TL0 1AD XXX CJW GGG
060389,000168:
|
|
Page 1409
|
060391,000170: # 2PHSCHNG IS USED WHEN ONE WISHES TO START UP A GROUP OR CHANGE A GROUP WHILE UNDER THE CONTROL OF A DIFFERENT
060392,000171: # GROUP. FOR EXAMPLE, CHANGE THE PHASE OF GROUP 3 WHILE THE PORTION OF THE PROGRAM IS UNDER GROUP 5. ALL 2PHSCHNG
060393,000172: # CALLS ARE MADE IN THE FOLLOWING MANNER,
060394,000173: # TC 2PHSCHNG
060395,000174: # OCT XXXXX
060396,000175: # OCT YYYYY
060397,000176: # WHERE OCT XXXXX MUST BE OF TYPE A AND OCT YYYYY MAY BE OF EITHER TYPE A OR TYPE B OR TYPE C. THERE IS ONE
060398,000177: # DIFFERENCE --- NOTE- IF LONGBASE IS TO BE SET THIS INFORMATION IS GIVEN IN THE OCT YYYYY INFORMATION, IT WILL
060399,000178: # BE DISREGARDED IF GIVEN WITH THE OCT XXXXX INFORMATION. A COUPLE OF EXAMPLES MAY HELP,
060400,000179: # AD TC 2PHSCHNG SET TBASE3 AND IF A RESTART OCCURS START
060401,000180: # AD+1 OCT 40083 THE TWO ENTRIES IN 3.8 TABLE LOCATION
060402,000181: # AD+2 OCT 05025 THIS IS OF TYPE C, SET THE JOB TO BE
060403,000182: # AD+3 OCT 18000 TO BE LOCATION AD+4, WITH A PRIORITY 18,
060404,000183: # AD+4 FOR GROUP 5 PHASE INFORMATION
060405,000184:
060406,000185: 5372 COUNT 02/PHASE
060407,000186:
060408,000187: 5372 00004 2PHSCHNG INHINT # THE ENTRY FOR A DOUBLE PHASE CHANGE
060409,000188: 5373 50002 NDX Q
060410,000189: 5374 30000 CA 0
060411,000190: 5375 24002 INCR Q
060412,000191: 5376 54072 TS TEMPP2
060413,000192:
060414,000193: 5377 75023 MASK OCT7
060415,000194: 5400 60000 DOUBLE
060416,000195: 5401 54071 TS TEMPG2
060417,000196:
060418,000197: 5402 30072 CA TEMPP2
060419,000198: 5403 75072 MASK OCT17770 # NEED ONLY 1770, BUT WHY GET A NEW CONST.
060420,000199: 5404 00006 EXTEND
060421,000200: 5405 75004 MP BIT12
060422,000201: 5406 56072 XCH TEMPP2
060423,000202:
060424,000203: 5407 75001 MASK BIT15
060425,000204: 5410 54066 TS TEMPSW2 # INDICATES WHETHER TO SET TBASE OR NOT
060426,000205:
060427,000206: 5411 15415 TCF PHASCHNG +3
060428,000207:
060429,000208: 5412 00004 PHASCHNG INHINT
060430,000209: 5413 35017 CA ONE # INDICATESWE CAME FROM A PHASCHNG ENTRY
060431,000210: 5414 54066 TS TEMPSW2
060432,000211:
060433,000212: 5415 50002 NDX Q
060434,000213: 5416 30000 CA 0
060435,000214: 5417 24002 INCR Q
060436,000215: 5420 54065 TS TEMPSW
|
|
Page 1410
|
060438,000217: 5421 00006 EXTEND
060439,000218: 5422 35425 DCA ADRPCHN2 # OFF TO SWITCHED BANK
060440,000219: 5423 52006 DTCB
060441,000220:
060442,000221: 5424 E3,1400 EBANK= LST1
060443,000222: 5424 02451 20063 ADRPCHN2 2CADR PHSCHNG2
060444,000223:
060445,000224: 5426 22073 ONEORTWO LXCH TEMPBBCN
060446,000225: 5427 22006 LXCH BBANK
060447,000226: 5430 22073 LXCH TEMPBBCN
060448,000227:
060449,000228: 5431 75066 MASK OCT14000 # SEE WHAT KIND OF PHASE CHANGE IT IS
060450,000229: 5432 10000 CCS A
060451,000230: 5433 15474 TCF CHECKB # IT IS OF TYPE :B:
060452,000231:
060453,000232: 5434 30062 CA TEMPP
060454,000233: 5435 75011 MASK BIT7
060455,000234: 5436 10000 CCS A # SHALL WE USE THE OLD PRIORITY
060456,000235: 5437 15461 TCF GETPRIO # NO GET A NEW PRIORITY (OR DELTA T)
060457,000236:
060458,000237: 5440 50061 OLDPRIO NDX TEMPG # USE THE OLD PRIORITY (OR DELTA T)
060459,000238: 5441 31052 CA PHSPRDT1 -2
060460,000239: 5442 54070 TS TEMPPR
060461,000240:
060462,000241: 5443 30062 CON1 CA TEMPP # SEE IF A 2CADR IS GIVEN
060463,000242: 5444 75010 MASK BIT8
060464,000243: 5445 10000 CCS A
060465,000244: 5446 15465 TCF GETNEWNM
060466,000245:
060467,000246: 5447 30002 CA Q
060468,000247: 5450 54063 TS TEMPNM
060469,000248: 5451 30006 CA BB
060470,000249: 5452 00006 EXTEND # PICK UP USERS SUPERBANK
060471,000250: 5453 04007 ROR SUPERBNK
060472,000251: 5454 54064 TS TEMPBB
060473,000252:
060474,000253: 5455 35460 TOCON2 CA CON2ADR # BACK TO SWITCHED BANK
060475,000254: 5456 22073 LXCH TEMPBBCN
060476,000255: 5457 52006 DTCB
060477,000256:
060478,000257: 5460 02537 CON2ADR GENADR CON2
060479,000258:
060480,000259: 5461 50002 GETPRIO NDX Q # DON:T CARE IF DIRECT OR INDIRECT
060481,000260: 5462 30000 CA 0 # LEAVE THAT DECISION TO RESTARTS
060482,000261: 5463 24002 INCR Q # OBTAIN RETURN ADDRESS
060483,000262: 5464 15442 TCF CON1 -1
060484,000263:
060485,000264: 5465 00006 GETNEWNM EXTEND
|
|
Page 1411
|
060487,000266: 5466 50002 INDEX Q
060488,000267: 5467 30001 DCA 0
060489,000268: 5470 52064 DXCH TEMPNM
060490,000269: 5471 35016 CA TWO
060491,000270: 5472 26002 ADS Q # OBTAIN RETURN ADDRESS
060492,000271:
060493,000272: 5473 15455 TCF TOCON2
060494,000273:
060495,000274: 5474 5066 OCT14000 EQUALS PRIO14
060496,000275: 5474 0061 TEMPG EQUALS ITEMP1
060497,000276: 5474 0062 TEMPP EQUALS ITEMP2
060498,000277: 5474 0063 TEMPNM EQUALS ITEMP3
060499,000278: 5474 0064 TEMPBB EQUALS ITEMP4
060500,000279: 5474 0065 TEMPSW EQUALS ITEMP5
060501,000280: 5474 0066 TEMPSW2 EQUALS ITEMP6
060502,000281: 5474 0070 TEMPPR EQUALS RUPTREG1
060503,000282: 5474 0071 TEMPG2 EQUALS RUPTREG2
060504,000283: 5474 0072 TEMPP2 EQUALS RUPTREG3
060505,000284:
060506,000285: 5474 0073 TEMPBBCN EQUALS RUPTREG4
060507,000286: 5474 0000006 BB EQUALS BBANK
060508,000287:
060509,000288: 14,3762 BANK 14
060510,000289: 10,2000 SETLOC PHASETAB
060511,000290: 10,2000 BANK
060512,000291:
060513,000292: 10,2451 E3,1436 EBANK= PHSNAME1
060514,000293: 10,2451 COUNT 10/PHASE
060515,000294:
060516,000295: 10,2451 22073 PHSCHNG2 LXCH TEMPBBCN
060517,000296: 10,2452 30065 CA TEMPSW
060518,000297: 10,2453 75023 MASK OCT7
060519,000298: 10,2454 60000 DOUBLE
060520,000299: 10,2455 54061 TS TEMPG
060521,000300:
060522,000301: 10,2456 30065 CA TEMPSW
060523,000302: 10,2457 75072 MASK OCT17770
060524,000303: 10,2460 00006 EXTEND
060525,000304: 10,2461 75004 MP BIT12
060526,000305: 10,2462 54062 TS TEMPP
060527,000306:
060528,000307: 10,2463 30065 CA TEMPSW
060529,000308: 10,2464 74105 MASK OCT60000
060530,000309: 10,2465 56065 XCH TEMPSW
060531,000310: 10,2466 75066 MASK OCT14000
060532,000311: 10,2467 10000 CCS A
060533,000312: 10,2470 15426 TCF ONEORTWO
060534,000313:
|
|
Page 1412
|
060536,000315: 10,2471 30062 CA TEMPP # START STORING THE PHASE INFORMATION
060537,000316: 10,2472 50061 NDX TEMPG
060538,000317: 10,2473 54751 TS PHASE1 -2
060539,000318:
060540,000319: 10,2474 10066 BELOW1 CCS TEMPSW2 # IS IT A PHASCHNG OR A 2PHSCHNG
060541,000320: 10,2475 12511 TCF BELOW2 # IT:S A PHASCHNG
060542,000321:
060543,000322: 10,2476 12477 TCF +1 # IT:S A 2PHSCHNG
060544,000323: 10,2477 40072 CS TEMPP2
060545,000324: 10,2500 22072 LXCH TEMPP2
060546,000325: 10,2501 50071 NDX TEMPG2
060547,000326: 10,2502 52751 DXCH -PHASE1 -2
060548,000327:
060549,000328: 10,2503 10066 CCS TEMPSW2
060550,000329: 10,2504 12505 NOOP # CAN:T GET HERE
060551,000330: 10,2505 12511 TCF BELOW2
060552,000331:
060553,000332: 10,2506 40025 CS TIME1
060554,000333: 10,2507 50071 NDX TEMPG2
060555,000334: 10,2510 55051 TS TBASE1 -2
060556,000335:
060557,000336: 10,2511 10065 BELOW2 CCS TEMPSW # SEE IF WE SHOULD SET TBASE OR LONGBASE
060558,000337: 10,2512 12525 TCF BELOW3 # SET LONGBASE ONLY
060559,000338: 10,2513 12530 TCF BELOW4 # SET NEITHER
060560,000339:
060561,000340: 10,2514 40025 CS TIME1 # SET TBASE TO BEGIN WITH
060562,000341: 10,2515 50061 NDX TEMPG
060563,000342: 10,2516 55051 TS TBASE1 -2
060564,000343:
060565,000344: 10,2517 30065 CA TEMPSW # SHALL WE NOW SET LONGBASE
060566,000345: 10,2520 62523 AD BIT14COM
060567,000346: 10,2521 10000 CCS A
060568,000347: 10,2522 12523 NOOP # ***** CANT GET HERE *****
060569,000348: 10,2523 17777 BIT14COM OCT 17777 # ***** CANT GET HERE *****
060570,000349: 10,2524 12530 TCF BELOW4 # NO WE NEED ONLY SET TBASE
060571,000350:
060572,000351: 10,2525 00006 BELOW3 EXTEND # SET LONGBASE
060573,000352: 10,2526 30025 DCA TIME2
060574,000353: 10,2527 53136 DXCH LONGBASE
060575,000354:
060576,000355: 10,2530 40062 BELOW4 CS TEMPP # AND STORE THE FINAL PART OF THE PHASE
060577,000356: 10,2531 50061 NDX TEMPG
060578,000357: 10,2532 54750 TS -PHASE1 -2
060579,000358:
060580,000359: 10,2533 30002 CA Q
060581,000360: 10,2534 22073 LXCH TEMPBBCN
060582,000361: 10,2535 00003 RELINT
060583,000362: 10,2536 52006 DTCB
060584,000363: 10,2537 22073 CON2 LXCH TEMPBBCN
|
|
Page 1413
|
060586,000365: 10,2540 30062 CA TEMPP
060587,000366: 10,2541 50061 NDX TEMPG
060588,000367: 10,2542 54751 TS PHASE1 -2
060589,000368:
060590,000369: 10,2543 30070 CA TEMPPR
060591,000370: 10,2544 50061 NDX TEMPG
060592,000371: 10,2545 55052 TS PHSPRDT1 -2
060593,000372:
060594,000373: 10,2546 00006 EXTEND
060595,000374: 10,2547 30064 DCA TEMPNM
060596,000375: 10,2550 50061 NDX TEMPG
060597,000376: 10,2551 53435 DXCH PHSNAME1 -2
060598,000377:
060599,000378: 10,2552 12474 TCF BELOW1
060600,000379:
060601,000380: 5474 BLOCK 02
060602,000381: 4000 SETLOC FFTAG1
060603,000382: 4000 BANK
060604,000383:
060605,000384: 5474 COUNT 02/PHASE
060606,000385:
060607,000386: 5474 75004 CHECKB MASK BIT12 # SINCE THIS IS OF TYPE B, THIS BIT SHOULD
060608,000387: 5475 10000 CCS A # BE HERE IF WE ARE TO GET A NEW PRIORITY
060609,000388: 5476 15461 TCF GETPRIO # IT IS, SO GET NEW PRIORITY
060610,000389:
060611,000390: 5477 15440 TCF OLDPRIO # IT ISN:T, USE THE OLD PRIORITY
060612,000391:
060613,000392:
060614,000393:
End of include-file PHASE_TABLE_MAINTENANCE.agc. Parent file is MAIN.agc